Product Description

CORROSHIELD CHLORINATED RUBBER ANTI-CORROSIVE PAINT 4350 is made of modified acrylic chlorinated rubber, which has performances of Fast drying, good adhesive strength, tough film and excellent water-fast and all-weather. Suitable for use at low temperature. For maintenance and repair on its existing coating surface, old hard adhered film of chlorinated rubber shall not be removed, so that be convenient to application.

Intended uses

CORROSHIELD CHLORINATED RUBBER ANTI-CORROSIVE PAINT 4350 is suitable for the anti-corrosion of kinds of steel structures in both moderately and severely corrosive environment including offshore structures, ships, chemical plants, super storage tanks, tankers for rail way and bridges.

Coating Data

Colour: Red, grey, white, etc.

Gloss Level: > 70%

Volume Solids: 50%

Specific Gravity: 1.1 kg / litre

Typical Thickness: 30 macrons dry equivalent to 60 macrons wet

Theoretical Spreading Rate:

7.1 m 2 / litre at stated d.f.t and volume solid above. Practical rate allow appropriate loss factors.

Dry to touch: ≤ 2 hours

Fully Cured: ≤ 10 hours

Flash Point: 25 ℃

Application Details

Application Method: Airless spray, brush, roller

Nozzle Orifice: 0.4 ~ 0.5 mm

Nozzle Pressure: 150 kg / cm 2

Thinner: CORROSHIELD X005

Cleaner: CORROSHIELD X005

Recommend film thickness: 70 macrons dry equivalent to 140 macrons wet (Spraying at two times)

System Compatibility:

See also the compatible scheme recommended by Industrial Protective Coatings department of Suzhou Colourway Enterprise Development Co., Ltd.

Surface Preparation

1. For primed surface, this product will be applied as soon as dry to touch. For the surface to be coated for much more time, ensure to be cleaned and free from contamination such as grease, inorganic salt, duct, etc. And must be applied after fully drying.

2. For applying this product solely, any surface to be coated should thoroughly be cleaned and free from contamination such as grease, inorganic salt, duct and so on. And then abrasive blasting to Sa2-1/2 (ISO8501-1:1988), or manual / power tool cleaning to St 3 (ISO8501-1:1988).

Application Precautions

1. This material should be constantly and thoroughly agitated during spraying.

2 Surface temperature must always be a minimum of 3 ℃ above dew point. Consequently keep away from condensation which will be affected to the anti-corrosive performance of coatings.

3. CORROSHIELD CHLORINATED RUBBER ANTI-CORROSIVE PAINT 4350 contains the V.O.C. solvent, in confined spaces must provide adequate ventilation during application and drying.

Pack Size

15 litres in a 18 litre container

Storage

Storage Condition: Store in dry, shaded condition away from shining and heat source.

Shelf Life: 12 months minimum at 25 ℃ .

Additional Declaration

1. This product is intended for use only professional applicators in industry situations in accordance with the advice given on this sheet and containers. All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety and Environment Standard and regulations. If in doubt regarding the suitability of use of this product, consult Industrial Protective Coatings department of Suzhou Colourway Enterprise Development Co., Ltd for further advice.

2. We do not accept any liability for the accident resulting from use of this product together with ones other company produced without any written permission by Industrial Protective Coatings department of Suzhou Colourway Enterprise Development Co., Ltd.

3. In case of using this product in the purpose other than the advice given on this sheet, confirmation from our company should be firstly made.

 

SUZHOU COLOURWAY ENTERPRISE DEVELOPMENT CO., LTD

( Former: SUZHOU PAINT FACTORY )

ADD: SHENJIA ROAD , DONGQIAO INDUSTRY DEVELOPING ZONE, XIANGCHENG DISTRICT, SUZHOU

PHONE: 0512-65376968 65379581

FAX: 0512-65376978

WEB: Http://www.colour-way.com

ZIP:215152