| BA04-2各色高固份丙烯酸氨基烘漆 |
|
| |
1、组成 |
|
| |
该产品是由含羟基丙烯酸酯剂聚物、氨基树脂、各种着色颜料、有机溶剂和助剂调制而成。
|
|
| 2、性能： |
|
该产品具有漆膜光亮丰满、色彩鲜艳，物理机械性能好，耐候性、保色性好等特点，是一种兼装饰性和保护性为一体的高效、节能、省
资源、低污染的新型涂料。
|
|
| 3、用途 |
|
主要用于车辆、家用电器、高档仪器、仪表以及农用机械等要求保护装饰性较好的金属表面涂装。可以代替进口冰箱漆，亦了用于机械
出口产品的涂装。
|
|
| 4、主要技术指标： |
|
项目 |
指标 |
细度 μm ≤ |
20
|
色漆固含量 ％ ≥ |
68 |
干燥时间，
120±2℃
min≤ |
|
|
硬度 ≥ |
0.60 |
柔韧性 mm ≤ |
1 |
冲击强度 cm ≥ |
50 |
附着力 级 ≤ |
2 |
光泽 ％ ≥ |
90
|
耐水性 60hs |
不脱落，不起泡 |
|
|
| 5、使用说明 |
|
（1）、黑色金属表面宜先进行喷沙处理，再经磷化等处理，铝合金宜阴极处理，再喷涂H06-2环氧酯底漆，也可直接涂于处理好的铝板表面。
（2）、施工 以喷涂为主，亦可浸涂。常用稀释剂为X-4氨基稀释剂或二甲苯，施工粘度（涂-4粘度计25℃），一般以18-30秒为宜。
（3）、静电喷涂施工时可选择下列三种方法之一种。
A.加入BYK-ES80助剂，约3‰；B.二丙酮醇溶剂约20％；C.一缩二乙二醇单醋酸酯约15％，用量需调试决定。
（4）喷涂后工件应在室温通风处放置8-15分钟，然后再升温度焙烘。烘烤条件为：120
±2℃，45分钟；130±2℃，30分钟。
（5）不能与其他不同品种的涂料混合使用，不可用松节油、汽油等作为稀释剂。
|
|
| 6、标志、包装、贮存和运输 |
|
按Q/320500ZQ02-90《涂料产品标志、包装、贮存和运输规则》执行。有效贮存期为一年。
|
|
| BAo4-2 Baking High solid Acrylic-amino Enamel |
|
| 1、Composition |
|
| This product is composed of acrylic ester oligomer with hydroxy1 group,amino resin,pigments,organic solvent and additives. |
|
| 2、Performance |
|
This paint is possessed of a shiny and plump film in gay colours.It has the advantages of excellent physical mechanical characteristics,weather
tesistance and colour-holding.Both for decoration and protection ,it is a new paint with high-efficiency,low-pollution and resource-saving. |
|
| 3、Application |
|
It is a decorative coating ,used in metal surfaces of vehicles ,family electrical facilities,superior quality instruments and agricultural machinery which
better protection and decoration are demanded in .It can be either the substitute of imported refrigeratot paint or the decoration of exported mechanical
products. |
| 4、Maint technical index |
Item |
Index |
1)Fineness μm ≤
|
20
|
2)Solid Content of Paint % ≥ |
68 |
3)Drying time
120±2℃ min≤ |
45 |
4）Hardness ≥ |
0.60 |
5)Toughness mm ≤ |
1 |
6)Impact strength cm ≥ |
50 |
7)Adhesion,grade ≤ |
2 |
8)Gloss % ≥ |
90 |
9)Water resistance（ 60 hours） |
No peeling off and blistering |
|
| 5、Application directions |
1)The surface of ferrous metal should be pretreated with sand-blasting-and bonderizing .It is suitable for aluminium-alloy to be pretreated with cathode,
then be sprayed with the H06-2 epoxy ester primer or applied the pretreated surface of the aluminium board directly.
2)Mainly applied with spraying,dipping also will do.X-4 amino-thinner or xylene is available .In general,the best viscosity of aoolication(Ford cup No.4,
at 25℃
) is at the range of 8-30 seconds.
3)One of the following 3 ways may be available when electrostatic spraying:
ADD A.BAY-ES80 additive approx. 3‰
；
B.Diacetone alcohol solvent approx.20%;
C.Diglycol mono-acetate approx.15%
Note:The quantity debugging is needed.
4)Having been sprayed,the objcet should be placed in well-ventilation at room temperature for 8-15minutes,then heated up and baked .The baking
condition is at 120 ±2℃,45 minutes or at 120±2℃,30 minutes.
5)
Keep separate from ather kinds of coating ,or mixusing,Turpentine oil or petrol shouldn‘t be used as a thinner.
|
| 6、Mark,Package,Storage and Trancsportation |
Carry out Q/320500 ZQ02-90"The Regulations of Mark,Package,Storage and Transportation forPaint Products."
The storage life is one year.
|
|
|
<<返回